Exactly How to Install a Bath Tub
Exactly How to Install a Bath Tub
Blog Article
What are your insights and beliefs on A Step-by-Step Guide to Installing a Bathtub?
Setting up a bath tub isn't specifically rocket science, but it does need strong plumbing, woodworking, and also sometimes, tiling skills. Changing an old tub with a brand-new one is additionally a moderately difficult job. If the old tub is easily available, the project can move rapidly; if you need to open up a wall surface to get rid of the old bathtub and position the new bathtub, the task is much harder. In either case, the project is within a residence handyman's abilities, although you will certainly require an assistant to leave the old tub as well as set in the new one. Make sure you have certified yourself for the job and are comfortable trying it. As opposed to working with a specialist to take control of a halfway-completed job, it is better to consider employing one prior to you start. Chances are you might need a professional plumber to make tube links.
This article will certainly help you mount a new bath tub in your shower room if you have actually already acquired a brand-new bathtub and do not need to alter the setup of your previous supply of water pipelines.
Your tools as well as product checklist must consist of the following:
Removing Old Touches
If you need to replace old faucets with new ones as a part of your installment, then the first thing you must do is disconnect the water system. After doing so, activate the faucets to drain any type of water continuing to be in the system. The process of getting rid of the existing taps can be rather bothersome as a result of the restricted gain access to that is usually the case.
Use a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipes to the faucets. Have a cloth all set for the staying water that will originate from the pipes. As soon as the supply pipes have actually been eliminated, make use of the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from transforming during this procedure. Once the faucets have actually been removed, the holes in the bath/basin will have to be cleansed of any kind of old sealing compound.
Prior to going on to fit the new taps, compare the pipeline links on the old faucets to the new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will need a plastic port to avoid damages to the string. One end of the port fits on the plastic tail of the faucet as well as the various other end supplies a link to the existing supply pipelines.
If you require to fit a monobloc, after that you will certainly need decreasing couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next, place the faucet in the installing opening in the bath/basin making certain that the washing machines are in place between the tap and also the sink. Safeguard the tap in position with the supplier given backnut. Once the tap is safely in place, the supply pipelines can be attached to the tails of the faucets. The faucets can either be attached by using corrugated copper piping or with normal tap ports. The former type must be attached to the faucet finishes initially, tightening up just by hand. The supply pipelines can later be connected to the other end. Tighten both ends with a spanner after both ends have been connected.
Installing the Tub
Utilizing the two wooden boards under its feet, put the tub in the needed setting. The wooden boards are valuable in evenly spreading the weight of the bathtub over the location of the boards instead of concentrating all the weight onto 4 tiny factors.
The following objective is to make certain that the bath tub is leveled all round. This can be attained by examining the level as well as changing the feet on the tub up until the spirit level checks out level.
To set up taps, fit all-time low of the outermost versatile tap adapter to the ideal supply pipeline by making a compression join; then do the very same for the various other tap.
Switch on the supply of water as well as check all joints and brand-new pipework for leakages as well as tighten them if required. Fill the bathtub as well as additionally inspect the overflow outlet and the regular electrical outlet for leaks.
Ultimately, take care of the bath paneling as defined in the maker's instruction manual. Tiling and securing around the bathtub needs to wait up until the bathtub has actually been utilized at least when as this will resolve it right into its final placement.
Getting ready for the Installment
First of all, the supporting framework supplied with the bathroom ought to be fitted (if called for) according to the maker's guidelines. Next, fit the faucets or mixer to the bathtub. When suitable the tap block, it is necessary to make certain that if the tap includes a plastic washer, it is fitted in between the bath and also the taps. On a plastic bathroom, it is also practical to fit a supporting plate under the faucets system to prevent stress on the bathtub.
Fit the adaptable tap adapters to the bottom of the two faucets utilizing 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet with the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Ensure you use every one of the provided washing machines.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link the bottom of the overflow tube in a comparable manner.The bath must now be ready to be suited its final placement.
Tiling Around the Tub
In the location where the bath fulfills the floor tile, it is required to secure the joins with a silicone rubber caulking. This is very important as the installation can move sufficient to break an inflexible seal, causing the water to pass through the wall in between the bathroom as well as the tiling, bring about problems with wetness and possible leakages to the ceiling below.
You can select from a variety of coloured sealants to assimilate your fixtures as well as installations. They are sold in tubes as well as cartridges, and also are capable of sealing spaces as much as a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with twists of soaked newspaper or soft rope. Remember to always fill the tub with water before securing, to allow for the movement experienced when the tub remains in use. The sealant can split relatively very early if you do not take into consideration this motion before sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally conveniently available on the market. It is recommended to fit the ceramic tiles utilizing waterproof or water-proof glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We hope you liked our topic on Installing A Bathtub. Thanks for spending some time to read through our post. Liked our review? Please share it. Let someone else find it. I take joy in reading our article about How to Install a Bathtub.
Request Service Report this page